Your signature stays on your device
A signature is not like a logo. It is a personal mark that can be used to approve documents, so it is worth thinking about where you send an image of it.
Image Tracer runs entirely in your browser. The image is read and traced inside a Web Worker on your computer, and is never uploaded to a server. There is no account and no cloud history, so nothing is stored anywhere except the SVG file you choose to download. Once the page has loaded you can even disconnect from the internet and it keeps working.
The code is open source, so anyone can check that this is how it works.
How to turn your signature into an SVG
- Sign on plain white paper with a dark pen. A felt-tip or gel pen gives a bolder, more even line than a ballpoint.
- Scan it, or photograph it from straight above in good, even light.
- Crop the image close around the signature. Any phone or computer photo tool can do this.
- Drop the image on the converter above, or paste it with Ctrl+V or Cmd+V.
- Check the result. If the line looks too thin, broken, or has grey smudges around it, open it in the editor and adjust the Threshold.
- Click Download SVG.
Getting a good scan or photo
The quality of the result depends far more on the source image than on any setting. A few minutes here saves a lot of fiddling later.
Scanning
- Scan at 300 dpi or more. Higher resolution keeps the fine tapers at the start and end of strokes.
- Use the colour or greyscale setting rather than a pure black-and-white scan mode. Those modes apply their own crude threshold; the tracer's threshold does a better job.
Photographing with a phone
- Use daylight near a window or a bright, even lamp. Avoid the flash, which creates a hotspot and glare on glossy ink.
- Hold the phone parallel to the paper so the signature is not skewed.
- Watch out for your own shadow falling across the page. Shadows are the most common cause of grey blotches in the trace.
- Fill most of the frame with the signature rather than zooming in afterwards.
Settings for signatures
Signatures are a single colour, so Black & white mode is the right choice. Three settings do almost all the work.
Threshold
The Threshold decides which pixels count as ink. It starts at an automatic value calculated for your image, and the editor shows a histogram so you can see where ink and paper separate.
- Strokes broken or too thin? Move the threshold up so lighter pixels count as ink.
- Grey shadows or paper texture showing up? Move it down.
Switch the preview to Processed image to see the exact black and white mask being traced.
Blur
A small Blur of about 1 px smooths out paper grain and the slightly ragged edge of ballpoint ink. Keep it low; too much blur fattens the line and fills in small loops.
Ignore less than
Ignore less than removes specks of dust or paper texture. Raise it until stray dots vanish, but stop before you lose the dot on an i or a full stop that is part of your signature.
| Problem | Fix |
|---|---|
| Gaps in thin strokes | Raise Threshold |
| Grey patches or shadow | Lower Threshold, re-photograph in better light |
| Fuzzy, hairy edges | Blur 1 px |
| Dust specks | Raise Ignore less than |
| White ink on dark paper | Tick Invert image |
A transparent background, automatically
In Black & white mode only the ink becomes shapes. The paper is not traced and the SVG has no background rectangle, so your signature sits on a fully transparent background. Place it over a document, a coloured footer or a dark web page and only the ink shows.
The ink is filled black by default. Because it is a vector, you can change it to dark blue or any other colour in a vector editor, or by editing the fill value in the SVG markup.
What the SVG looks like
Each separate piece of the signature becomes its own <path>: the connected scrawl of a surname, an initial written apart, the dot over an i. In the example above, a 1000×340 px signature traces to 13 shapes and 1,405 nodes, in a file of about 24 KB.
The paths are filled outlines of the ink, not single pen strokes. That keeps the natural variation in line width, which is what makes a signature look handwritten.
Where to use your signature SVG
- Email signatures and websites: an SVG stays crisp on high-density screens, where a small PNG can look blurry.
- Letterheads and templates: scale it to fit without any loss of quality.
- Design work: artists signing digital prints or illustrations.
- Engraving and cutting: a clean outline is a good starting point for laser engraving or vinyl. See image to SVG for Cricut.
Image Tracer only converts the image. Whether an inserted signature image is acceptable for a particular document is a legal question that depends on where you are and what you are signing.
Frequently asked questions
Is it safe to convert my signature online here?
Yes. Although the tool is on a web page, the tracing runs locally in your browser. Your signature image is never uploaded, and there is no account or stored history.
Will the signature SVG have a transparent background?
Yes. Black & white mode only creates shapes for the ink. The paper is left out and there is no background rectangle, so the background is transparent.
Can I use a phone photo instead of a scanner?
Yes. Photograph from straight above in even daylight, without flash or shadows, and crop close. Adjust the Threshold if the strokes come out too thin or grey patches appear.
How do I make the signature blue instead of black?
Open the SVG in a vector editor and change the fill colour of the paths, or edit the fill attribute in the SVG markup with any text editor.
Why does my signature look thicker or thinner than the original?
The Threshold sets where ink ends and paper begins. Lower it for a thinner line, raise it for a thicker one, and keep Blur at 0 or 1 px.
Last updated

